Lumasense-technologies IN 2000 Uživatelský manuál stáhnout pdf (Strana 17)

IMPAC Infrared sensor IN 2000

12 Data format UPP



(Universal Pyrometer Protocol)

Via interface and suitable communication software or via “Test” function of the InfraWin software (see 8,

Basic settings  Test) commands can be exchanged directly with the pyrometer.

The data exchange occurs in ASCII format with the following transmission parameters:

The data format is: 8 data bits, 1 stop bit, even parity (8,1,e)

The device responds to the entry of a command with: output (e.g. the measuring value) + CR (Carriage

Return, ASCII 13), to pure entry commands with “ok” + CR.

Every command starts with the 2-digit device address AA (e.g. “00”).

This is followed by 2 small command

letters (e.g. “em” for level of emissivity

), finished with CR

This is followed, if necessary for that command, by the ASCII parameter “X”. If this parameter “X” is omitted,

then the device resets with the current parameter.

A “?“ after the small command letters answers with the respective settings (only at setting commands, not at

enquiry commands).

Example: Entry: “00em“ + CR

The emissivity setting (ε) of the device with the address 00 is returned

Answer: “0970“ + CR means Emissivity = 0.97 or 97.0%

Description Command Parameters

Reading temperature

value:

AAms Output: XXXXX (in 1/10 °C oder °F)

(88880 = Temperature overflow)

Reading temperature

value repeated:

AAmsXXX XXX = 001...999 (XXX = number of measuring values)

Emissivity ε: AAemXXXX XXXX = (0010 ... 1000‰) (decimal)

Exposure time t

: AaezX X = 0 ... 9 (decimal) 0 = intrinsic time constant of the device

1 = 0,50 s 4 = 5,00 s 7 = 60,00 s

2 = 1,00 s 5 = 10,00 s 8 = 90,00 s

3 = 2,00 s 6 = 30,00 s 9 = 120,00 s

Clear time maximum

value storage:

AAlzX X = 0 ... 8 (dec.) 0 = Maximum value storage off

1 = 0.1 s 4 = 1.00 s 7 = (not available)

2 = 0.25 s 5 = 5.00 s 8 = automatically deletion

3 = 0.5 s 6 = 25.00 s

Reading basic tem-

perature range:

AAmb Output: XXXXYYYY (hex 8-digit, °C)

XXXX = beginning of temperature range

YYYY = end of temperature range

Reading temperature

sub range:

AAme Output: XXXXYYYY (hex 8-digit, °C)

XXXX = beginning of temperature range

YYYY = end of temperature range

Setting of temperature

sub range:

AAm1XXXXYYYY XXXX (hex 4-digit) beginning of temp. range (°C)

YYYY (hex 4-digit) end of temp. range (°C)

Address: AAgaXX XX = (00 ... 97) 00 ... 97 = adjustable addresses

Baud rate: AAbrX X = 3...4

3 = 9600 Baud 4 = 19200 Baud

Changing °C / °F AAfhX Output: X = 0: display in °C; X = 1: display in °F

Internal temperature: AAgt Output: XX (decimal 00 … 98, in °C)

XXX (decimal 032 … 208°F)

Max. internal

temperature:

AAtm Output: XX (decimal 00 … 98, in °C)

XXX (decimal 032 … 208°F)

Error status: AAfs Output 1 byte hex (00 = no error)

Reading parameters: AApa Output decimal 11-digit:

Digit 1 und 2 (10...99 or 00): Emissivity

Digit 3 (0 ... 9): Exposure time

Digit 4 (0 ... 8): Clear time max. storage

Digit 5 (1): Analog output

Digit 6 and 7: (00 ... 98): Internal temperature

Digit 8 and 9 (00 ... 97): Address

Digit 10 (3 … 4): Baud rate

Digit 11 (0): always 0

Device type: AAna Output: “IN 2000”

Serial number: AAsn Output: XXXX (hex 4-digit)

Device type /

software version:

AAve Output: XXYYZZ (6-digit decimal)

XX = 77 (IN 2000)

YY = Month of software version

ZZ = Year of software version

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 35 36

Komentáře k této Příručce

Žádné komentáře

Lumasense-technologies IN 2000 Uživatelský manuál Strana 17

Komentáře k této Příručce

Související produkty a manuály pro Nástroje Lumasense-technologies IN 2000