Lumasense-technologies M390S Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Nástroje Lumasense-technologies M390S. LumaSense Technologies M390S User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - Blackbody Calibration Source

MANUA LM390SBlackbody Calibration Source

Strany 2

M390S Manual Introduction  102.2 Technical DataThis Model Model Temperature Range[ ] M390-S 600 to 3000 °C (1110 to 5430 °F) Custom split designAc

Strany 3 - Contents

M390S Manual Installation  113 Installation3.1 Installing the M390STo install the M390S:1. Allow the M390 to warm-up to room temperature for at leas

Strany 4 - M390S Manual Contents  iv

M390S Manual Installation  12To ensure consistent document formatting, this page was intentionally left blank.

Strany 5 - 1 General Information

M390S Manual Operation  134 Operation4.1 Starting UpTo start up the M390S:1. Turn on the power switch/breaker and allow 20 seconds for the system to

Strany 6 - 1.4 Unpacking the Instrument

M390S Manual Operation  14Eurotherm controller4.2.1 Other Controller ModesIf, for some reason, the power must be turned off while monitoring tempera

Strany 7

M390S Manual Operation  159. Press the PAGE button until ACCESS appears.10. Press the SCROLL button.11. Press the DOWN button until LEVEL 1 appears

Strany 8

M390S Manual Operation  164.5.1 RS485 OptionRS485 two wire is available as an option. The connection scheme is shown below:RS485 for multi-drop app

Strany 9 - 2 Introduction

M390S Manual Operation  174.6 PID Tuning ConstantsThe PID tuning constants have been factory set for optimum performance and are noted below.Heating

Strany 10 - 2.2 Technical Data

M390S Manual Operation  18Typical Radiance temperature calibration look-up table (LUT) usedTo gain access to the custom look-up table:Refer to the 4

Strany 11 - 3 Installation

M390S Manual Operation  19Note: Calibration points do not have to be used as pre-programmed. To dial in adifferent calibration point, simply change

Strany 12

Confidential InformationThe material contained herein consists of information that is the property of LumaSenseTechnologies and intended solely for us

Strany 13 - 4 Operation

M390S Manual Operation  20To ensure consistent document formatting, this page was intentionally left blank.

Strany 14 - 4.3 Shutting Down

M390S Manual Maintenance  215 Maintenance5.1 Cavity LifeThe life expectancy of the graphite cavity depends on the time and temperature of operation.

Strany 15 - M390S Manual Operation  15

M390S Manual Maintenance  225.4 Furnace Core DisassemblyThe graphite core can be replaced without disconnecting cooling or purge tubing. Refer toexp

Strany 16 - 4.5.1 RS485 Option

M390S Manual Maintenance  23Refer to the Appendix for an exploded view of the cavity assembly.5.5 Fuse LocationsThe M390 has several fuses. Refer t

Strany 17 - 4.7 Controller Calibration

M390S Manual Maintenance  245.6 CleaningClean the outside of the cabinet with mild soapy solution and water only. Do not attempt toclean the emitte

Strany 18 - M390S Manual Operation  18

M390S Manual Index  25IndexCCavity life 21Cleaning 24Controller Calibration 17Controller Modes 14DDisposal 7EEurotherm iTools Software 17FFurnace Co

Strany 19 - M390S Manual Operation  19

M390 Manual Index  26To ensure consistent document formatting, this page was intentionally left blank.

Strany 20 - M390S Manual Operation  20

M390 Manual Appendix A: Drawings  27Appendix A: Drawings

Strany 21 - 5 Maintenance

M390 Manual Appendix A: Drawings  28

Strany 22 - 5.4 Furnace Core Disassembly

M390 Manual Appendix A: Drawings  29

Strany 23 - 5.5 Fuse Locations

M390S Manual Contents  iiiContents1 General Information ...

Strany 24 - 5.6 Cleaning

M390 Manual Appendix B: ASCII/BASIC  30Appendix B: ASCII/BASICTypical ASCII request string to read the blackbody temperature:'-------make a req

Strany 25 - M390S Manual Index  25

M390 Manual Appendix B: ASCII/BASIC  31A simple BASIC program to send blackbody setpoint:CLS'-----open comm port 1 for 9600 baud, 7,E,1-----OPE

Strany 26 - M390 Manual Index  26

M390 Manual Appendix C: Declaration of Conformance  32Appendix C: Declaration of Conformance

Strany 27 - Appendix A: Drawings

M390S Manual Contents  ivAppendix A: Drawings ...

Strany 28

M390S Manual General Information  51 General Information1.1 Information about the user manualCongratulations on choosing the high quality and highly

Strany 29

M390S Manual General Information  6Warning: DO NOT USE NITROGEN (N2) FOR PURGE GAS. AT HIGH TEMPERATURES,CYNIDE GAS COULD BE GENERATED.1.3 Limit of

Strany 30 - Appendix B: ASCII/BASIC

M390S Manual General Information  7Return the instrument upon receipt of the RMA nµmber, transportation prepaid. Clearlyindicate the assigned RMA nµ

Strany 31

M390S Manual General Information  8To ensure consistent document formatting, this page was intentionally left blank.

Strany 32

M390S Manual Introduction  92 Introduction2.1 DescriptionThe M390 series are high temperature blackbody calibrators that can produce a very hightemp

Komentáře k této Příručce

Žádné komentáře